Flash UV Adhesive Safety Data Sheet
Flash UV Adhesive Safety Data Sheet
SECTION 1 – CHEMICAL PRODUCT AND COMPANY ID
1.1 Product Name : FLASH UV Adhesive
1.2 First Issue : 12 September 2024
1.3 Company Identification : Lash Envy Professional
6a Haughton Road Oakleigh VIC 3166 AUSTRALIA
SECTION 2 – INGREDIENTS
Ethyl Cyanoacrylate 89%
Polymethyl Methacrylate 10%
Methanone, [bis(4-methylphenyl)phosphinyl] (2,4,6-trimethylphenyl) 0.7%
Carbon Black 0.3%
SECTION 3 – HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Flammable liquid in case of open flame. Vapour may irritate eyes, skin and respiratory tract. Polymerises when exposed to UV light.
POTENTIAL HEALTH EFFECTS
Inhalation or ingestion in large quantities may cause breathing difficulties and respiratory tract irritation.
Long term exposure may cause skin irritation.
Eyes: Irritation
POTENTIAL ENVIRONMENTAL EFFECTS
Before curing the substance has no direct environmental harm. After curing, the polymerised product has no direct environmental hazard. Large spills may be harmful to aquatic organisms.
SIGNS AND SYMPTOMS OF EXPOSURE
Vapour may cause irritation to eyes and mucous membranes. Prolonged exposure may cause respiratory discomfort or skin irritation.
EXISTING CONDITIONS AGGRAVATED BY EXPOSURE
None Known.
SECTION 4 – FIRST AID MEASURES
Inhalation: Move to fresh air immediately. Keep airway clear. If breathing is difficult, seek medical attention.
Skin contact: Remove contaminated clothing. Wash thoroughly with water and soap. Do not pull bonded skin apart.
Eye contact: Immediately flush with running water or saline for at least 15 minutes. Seek medical attention.
Ingestion: Ensure airway is clear. Rinse mouth with water. Seek medical advice immediately.
Notes to physician: Treat symptomatically. Adhesive polymerises rapidly. Passive, non surgical separation of bonded tissue is recommended.
SECTION 5 – FIRE FIGHTING MEASURE
Flash Point: Flammable in case of open fire
Extinguishing Agents: Foam, carbon dioxide, dry powder, sand
Special Firefighting Procedures: Firefighters must wear gas masks and full protective clothing. Cool containers with water spray.
Hazardous Products Formed by fire or thermal decomposition: Carbon monoxide CO and carbon dioxide CO2
Unusual fire or explosion hazards: No explosion risk identified
SECTION 6 – ACCIDENTAL RELEASE MEASURES
Personal precautionary measures: Refer to section 8 – personal protection. Evacuate personnel and restrict access. Remove ignition sources.
Environmental protection measures: Prevent entry into drains and waterways. Large quantities may be harmful to aquatic life.
Procedure for cleaning/absorption: Absorb small spills with sand or inert material. For large spills build containment and transfer to appropriate waste disposal facility.
SECTION 7 – HANDLING AND STORAGE
7.1 HANDLING:
Provide good ventilation. Keep away from heat and open flame. Avoid contact with skin and eyes.
Do not smoke in work area. Use appropriate protective equipment.
Polymerises rapidly under UV light exposure. Avoid unnecessary UV exposure during handling.
7.2 STORAGE:
Store in a cool, dry, well ventilated location. Keep container tightly closed.
Keep away from heat, moisture and direct sunlight.
7.3 OTHER PRECAUTIONS:
Wash hands and face after handling.
Practice good personal hygiene before eating, drinking or smoking.
Keep out of reach of children.
SECTION 8 – EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering controls: Ensure adequate ventilation during use. Provide eyewash facilities.
Respiratory protection: Use respirator if vapour exposure exceeds recommended limits.
Eye protection: Wear protective glasses or face shield.
Hand protection: Wear chemical resistant gloves.
Body protection: Wear appropriate protective clothing.
SECTION 9 – PHYSICAL AND CHEMICAL PROPERTIES
Appearance : Gray Liquid
Odor : Slight pungent smell
Boiling Point : No information available
Melting Point : N/A
Specific Gravity : No information available
Vapor Pressure : No information available
Vapour Density : No information available
Solubility in Water : Insoluble
Additional information : Soluble in toluene and similar organic solvents. Polymerises under UV light.
SECTION 10 – STABILITY AND REACTIVITY
10.1 Conditions to avoid: Heat, moisture and UV exposure during storage
Stability : Stable at room temperature
Material to avoid: Strong oxidants, alkalis
Hazardous Decomposition or by Products: Carbon monoxide CO, carbon dioxide CO2
SECTION 11 – TOXICOLOGICAL INFORMATION
Toxicity: May cause irritation to skin, eyes and respiratory tract.
Possible Routes of Entry: Inhalation Yes, Skin Yes, Ingestion Yes.
SECTION 12 – ECOLOGICAL INFORMATION
Large releases may be harmful to fish and aquatic organisms before curing. Polymerised product is not considered environmentally hazardous.
SECTION 13 – DISPOSAL CONSIDERATIONS
Product: Dispose of as hazardous waste according to local regulations. Do not pour into waterways.
SECTION 14 – TRANSPORTATION INFORMATION
Road transport: Not restricted under normal packaging conditions.
Transport method: By air, sea, railway or road.
Transportation precautions: Ensure packaging is secure and intact. Do not transport with oxidising agents, alkalis or food products.
SECTION 15 – REGULATORY INFORMATION
Complies with relevant EU CLP Regulation EC No 1272/2008
REACH Regulation EC No 1907/2006
Commission Regulation EU 2020/878
SECTION 16 – OTHER INFORMATION
Estimated NFPA Code:
Health Hazard 1
Fire Hazard 1
Reactivity Hazard 1
Specific Hazard Does not apply
Estimated HMIS Code:
Health Hazard 1
Flammability Hazard 1
This information is furnished without warranty, express or implied, except that it is accurate to the best knowledge of Lash Envy Professional. It relates only to the specific material designated herein and does not relate to use in combination with any other material or process. Lash Envy Professional assumes no responsibility for use or reliance upon this information.